Hey folks! So sorry for this coming so late. This one was the hardest one to do yet, not to mention, I had a few personal setbacks. (Namely my youngest daughter took my camera one day without asking! :D )
This is the final installment but I will still be happy to answer any of your questions. Just post them here.
I hope you will come back later this week for a special surprise!
Monday, February 7, 2011
Thursday, January 27, 2011
Viking Knit Tutorial-Step 2:Knitting your chain
This week I tried my hand at "Vlogging". Let me tell you...it was NOT easy!
If you have a question you would like answered in an upcoming segment, please let me know! See ya next week!!
If you have a question you would like answered in an upcoming segment, please let me know! See ya next week!!
Thursday, January 20, 2011
TUTORIAL-Viking Knit Chain-Part 1-Wooden Drawplate
Over the next few weeks I will be covering Viking Knit Chain. This week we will start with one of the last items you will use: the Wooden Drawplate. I use a wooden one for a number of reasons:
1)Inexpensive-These aren't as durable as the metal ones, but they can be remade in minutes.
2)Good for approximately 10 chains.
3)Made with easy to acquire supplies.
4)A very quick project!
Lets get started!
**SAFETY FIRST**
Remember, you will be working with power tools so safety glasses are a MUST!
Tie long hair back. Do not wear loose clothing. PAY ATTENTION to what you are doing!
Supplies:
Heavy duty Paint stir stick (available for free at the hardware store)
Sharpie pen
Sandpaper
Drill Bit Conversion Chart
Tools:
Drill motor and drill bits (I have used a mix of standard and metric but you can use whatever will get you the size holes you will need)
Step 1:
Lay your paint stick onto a surface that you can drill on. I use a scrap 2X4.
Insert a drill bit into the drill. (I have used a standard size E because this is the closest to the size of my finished Viking knit chain.)
Near the top left corner of your paint stick, slowly drill through.
Flip your paint stick over and carefully drill into the hole you have just made. (This helps with clean-up)
Step 2:
Using the Drill bit Conversion chart, look up the size of your drill bit. Millimeters works best. **When my bit isn't listed, I use my calipers to measure it.**
Use your sharpie and write this measurement above the hole. (In this case it was 6.350 mm)
Step 3:
Choose a slightly small bit and repeat step 1 above.
I chose Standard size 8.
Step 4:
Repeat step 2. (In this case 5.055 mm)
Step 5 through Step10:
5: Choose a slightly small bit and repeat step 1 above.
I chose Standard size 14.
6: Repeat step 2. (In this case 4.623 mm)
7: Choose a slightly small bit and repeat step 1 above.
I chose Metric size .172.
8: Repeat step 2. (In this case 4.33 mm)
9: Choose a slightly small bit and repeat step 1 above.
I chose Metric .156.
10: Repeat step 2. (In this case 3.91 mm)
Step11:
Lightly sand front and back. Be sure to run sandpaper into each hole as well.
Now you have your first tool towards your Viking Knit Chain! You can expect to have to cut this portion off the paint stick and redo this about every 10 times you use it.
Be sure to come back next week, when we will be getting started with our chains!
1)Inexpensive-These aren't as durable as the metal ones, but they can be remade in minutes.
2)Good for approximately 10 chains.
3)Made with easy to acquire supplies.
4)A very quick project!
Lets get started!
**SAFETY FIRST**
Remember, you will be working with power tools so safety glasses are a MUST!
Tie long hair back. Do not wear loose clothing. PAY ATTENTION to what you are doing!
Supplies:
Heavy duty Paint stir stick (available for free at the hardware store)
Sharpie pen
Sandpaper
Drill Bit Conversion Chart
Tools:
Drill motor and drill bits (I have used a mix of standard and metric but you can use whatever will get you the size holes you will need)
Step 1:
Lay your paint stick onto a surface that you can drill on. I use a scrap 2X4.
Insert a drill bit into the drill. (I have used a standard size E because this is the closest to the size of my finished Viking knit chain.)
Near the top left corner of your paint stick, slowly drill through.
Flip your paint stick over and carefully drill into the hole you have just made. (This helps with clean-up)
Step 2:
Using the Drill bit Conversion chart, look up the size of your drill bit. Millimeters works best. **When my bit isn't listed, I use my calipers to measure it.**
Use your sharpie and write this measurement above the hole. (In this case it was 6.350 mm)
Step 3:
Choose a slightly small bit and repeat step 1 above.
I chose Standard size 8.
Step 4:
Repeat step 2. (In this case 5.055 mm)
Step 5 through Step10:
5: Choose a slightly small bit and repeat step 1 above.
I chose Standard size 14.
6: Repeat step 2. (In this case 4.623 mm)
7: Choose a slightly small bit and repeat step 1 above.
I chose Metric size .172.
8: Repeat step 2. (In this case 4.33 mm)
9: Choose a slightly small bit and repeat step 1 above.
I chose Metric .156.
10: Repeat step 2. (In this case 3.91 mm)
Step11:
Lightly sand front and back. Be sure to run sandpaper into each hole as well.
Now you have your first tool towards your Viking Knit Chain! You can expect to have to cut this portion off the paint stick and redo this about every 10 times you use it.
Be sure to come back next week, when we will be getting started with our chains!
Thursday, January 13, 2011
Retooling and seeking my Muse
It happens to every creative soul you know. Their Muse goes on an extended vacation.
On December 23, 2010, my Muse packed her bags, flipped me off, screamed something at me that contained the "F" word and slammed the door on the way out!
Im not sure what I did to offend her. Maybe I over worked her over the holidays. It wasn't intentional, there was lots to be done! Maybe it was stress. We did have a lot of guests. Maybe it was just the holidays in general. There is a tremendous amount of activity involved. Or, maybe she was overwhelmed by all the new tools I bought and was given. I just cant put my finger on it.
Ive tried working without her. I thought she might see how much fun I was having without her, decide she'd been too hasty and come back. Alas, that didn't work. Ive posted her pictures on milk cartons, cereal boxes and hung signs around the neighborhood. Nothing. I suspect she may be hanging out at my friends house because they are redoing their interior. The work is moving along rather quickly, so I'm sure they wont let me know if that's where shes hiding.
Im posting this note, in hopes that if any of you see her or hear from her, you will pass it along:
Dear Musey Muse, (Thats what I call her)
I have missed you so much! If you will PLEASE just come back, I PROMISE!!, I'll do more of the work! I will sketch more, play more and take over as much as I can. I will work to learn new things, try not to worry about the price of the silver I'm ruining, or tell you to "get off your lazy ass and get busy" any more. Ive been a bad partner and I acknowledge that.
I love you, I need you, and I am NOTHING without you!
All My Love,
G-pers (Thats what she calls me)
PLEASE, pass my message on to her.
On December 23, 2010, my Muse packed her bags, flipped me off, screamed something at me that contained the "F" word and slammed the door on the way out!
Im not sure what I did to offend her. Maybe I over worked her over the holidays. It wasn't intentional, there was lots to be done! Maybe it was stress. We did have a lot of guests. Maybe it was just the holidays in general. There is a tremendous amount of activity involved. Or, maybe she was overwhelmed by all the new tools I bought and was given. I just cant put my finger on it.
 |
| This piece was ok, but certainly not "inspired". |
Im posting this note, in hopes that if any of you see her or hear from her, you will pass it along:
Dear Musey Muse, (Thats what I call her)
I have missed you so much! If you will PLEASE just come back, I PROMISE!!, I'll do more of the work! I will sketch more, play more and take over as much as I can. I will work to learn new things, try not to worry about the price of the silver I'm ruining, or tell you to "get off your lazy ass and get busy" any more. Ive been a bad partner and I acknowledge that.
I love you, I need you, and I am NOTHING without you!
All My Love,
G-pers (Thats what she calls me)
PLEASE, pass my message on to her.
Wednesday, January 5, 2011
'Ugly Boleyn???'
Even though I was born in England, Ive never had any interest in English History. (YAWN) Recently that changed when I watched 'The Tudors'. I LOVED the story (however improvised for this series) of Henry VIII and his six wives. BUT, more than the story....I LOVED the jewelry!!! Everyone wore it! Men in HUGE chains, women in multiple chains and pendants, rings, rings and more rings!! I was inspired!
I created my own 'Tudors' piece. Or at least I "thought" it was a 'Tudors' inspired piece...
Now all of a sudden I am obsessed with all things 'Tudor'! I'm researching the British Monarchy, I'm watching documentaries and any movie I can think of to see more of this jewelry! Thats when it happened......my crushing realization.....
these are movie and television prop, not replicas of actual pieces!!! How do I know?
WELL, unless this is the "other", other Boleyn girl.....
I haven't really suffered a huge loss. I was inspired to make my own inspired piece and I'm of the opinion that it came out quite nice. Now I have to ask...What inspires you?
 |
| The cast of 'The Tudors' season 2 |
 | |||
| http://www.etsy.com/listing/54877950/dyed-jasper-pearl-swarovski-crystal-and |
Now all of a sudden I am obsessed with all things 'Tudor'! I'm researching the British Monarchy, I'm watching documentaries and any movie I can think of to see more of this jewelry! Thats when it happened......my crushing realization.....
 | |||||||
| 'The Other Boleyn Girl'-notice Natalie Portman's necklace |
 |
| America Ferrera as Ugly Betty |
I haven't really suffered a huge loss. I was inspired to make my own inspired piece and I'm of the opinion that it came out quite nice. Now I have to ask...What inspires you?
Saturday, February 6, 2010
The Challenge-Process
Back at the beginning of January, a friend showed me a beautiful Snow White Druzy. As soon as I saw it, I KNEW I had to have it! (So I STOLE it!! Bought it right out from under her!! I didn't really even mind the fact that she had licked it....much!) I had absolutely NO clue what I would do with it, but it was so unbelievably beautiful; I bought it!
When it arrives I am shocked by how large it is. It measures 2 inches tall by 1 and a half inches wide....by far and away the largest stone I will have worked with.
Now its design time and the ONLY thing I can do to stabilize it is a prong mount. All I can think is, "How ordinary!". I have an aversion to "ordinary".
I go to work by making my prong mounting; which, at this point, is very rudimentary. Once I have completed that I start looking at how best to accentuate this stone. Now something happens to me that hasn't happened before....I become paralyzed with fear! I'm not sure why. I have messed up PLENTY of metal before! I head to my forum. "Go for it", is the response I get!
That's when it happened.....I became very Zen with this project and it flowed! I cut out a sheet of silver to act as a collar and stamped the words, live, laugh. and love on it. I then soldered it closed and....the stone still fit!!! (I had anticipated a failure here!) Now comes the tricky part....I have to mount this collar into my prong setting, allowing enough space below the stone for the stone to be held securely in the prong mount. Okay so here....I improvised. I placed the stone into the collar and set the whole thing into the prong mount and marked the placement with a sharpie. (HEY! whatever works! Right?)
I did the BEST pic soldering I have EVER done and Wa-La the mount is done!! Now to add a bail!
I had one filigree bead left and I was determined to use it on this project! Problem was....it was small. I know...add tubing!!! (At this point I MUST thank whoever suggested the hobby tube cutter to me! It was the best seven bucks Ive spent!!) Again I pic solder; first to attach the tubing to the bead, then to attach the bail to the pendant.
I wont go into detail here as this is the dull point where I clean up the setting and mount the stone.
At the end of the day I cant explain how I felt! I had ventured out of my comfort zone, put all the lessons I had learned in Metalsmithing to use, and completed an exceptional piece!
Sunday, January 10, 2010
A learning experience
So Ive been joining in on a Metalsmithing Forum since September. It is, without a doubt, one of the best things Ive ever done for myself! I belong to a number of groups that have information on jewelry making. None, other than this one, allows me to ask a question and get an answer within minutes.
There are Metalsmiths of all levels in this group. From the novice (like myself) to seriously seasoned pro's! We like to think of ourselves as the "un-team Team and we welcome anyone....provided you give us your first name and DO NOT spam us! :D
Back around November we decided that we loved each others work so much that we wanted to share! At first it was suggested that we have a pendant swap! Well, I was all for this! This was an opportunity to really shine! It was going to be a masterpiece! Before I could finish dreaming, it had changed and now, we were doing a charm swap. Ok, still alright.....I think.
I immediately started sketching. I wanted to play on my strengths. *What were my strengths again?* Oh yeah, I have none. Well, maybe one; I am not afraid to REALLY screw up some metal! I mean I will try ANYTHING!! Usually with disastrous results, but hey that's how you learn, right? **Not to mention all the incredible scrap metal you produce!**
So I started with a triangle. My thinking being that 1) not everyone would be doing it and 2) it took less metal. (At this writing, silver prices are $18.44 a ounce!!!!) So I mark them and start cutting. NO GOOD! I wont be able to anything on them once I'm finished. Back to the drawing board.
November turns to December and all I have are sketches. Now I'm busy preparing for Christmas. Still no progress. That's when it hit me....wait to see what you get for Christmas, then you will know what to do.
Well I got a disc cutter, drill bits, a caliper and gift certificates to the supply house!
"The disc cutter will help", I think. "They are going to be round"!
STEP ONE: Determine a shape. Check!
So I order metal. Not much, but enough to make the charms. I have TONS of copper, but I haven't soldered it much before and I really want them to be silver!
STEP TWO: Order metal. Check.
The Sterling silver arrives and I cant wait to try out my new disc cutter. Okay, so lets just say, sometimes it worked and sometimes it didn't. **Operator problems** I was still able to get 10 usable discs from it. **And 3 unusable ones but we will refer to those as "future opportunities"!**
STEP THREE: Cut the metal. Check.
Now I have to ask myself, "Where do we go from here"? I look at my sketches again....nothing there that speaks to me.
WAIT! I HAVE IT! I have been doing a series of pieces about water. I don't know why. I am not particularly fond of water except as my drink of choice but at least this is a direction. Ok. water, water, water....."the flow"! Why "the flow"? I guess because I have a hard time going with it; this will serve as a reminder!
STEP FOUR: Choose a design and make these bad boys! Check.
Now I'm on a roll! So I stamp "flow" onto them! "The" is irrelevant. That worked.
Now what? Okay, I have a huge amount of inexpensive aquamarines, so I add a setting! **YOU GO GIRL!!!** So far, so good!
I then add my "water" (Silver wire that I have hammered flat and curved around my settings). Still, all good!
Time to cut the settings. (This is where the problems started!) You see, I had this tank of fuel that was running out, but I INSISTED on using it until the bitter end. So I solder away, pickle, rinse, and start to cut the settings......RIP! Off comes the setting. Rocketing across the room and now a two hour search is underway! Okay, I recovered it. Not sure what happened but I will fix that later. Lets try another...RIP!!! What is going on?!?!
I RUN to the computer and ask the forum. Bad soldering or too long in the pickle is the response I get. I know it wasn't in the pickle too long, so bad soldering it is! Now I remember that I have soldered 5 settings before I changed that tank, and 5 it is! Five settings rip off!
Its okay, I'm cool. Ill fix them later. Work with what you have.
The biggest problem is, these suckers are little! It hard to hold onto them while you cut them! I mention this to my husband and he says, "Use your shelf paper". (Like he'd been doing this his entire life and this was the OBVIOUS answer!!!) But it worked!!!
I repair one of the broken settings **just to see if I can**! Okay, Its holding up, but I'm getting anxious! What if they look like crap?
So I work on the six I have cut. I set the stones, polish and tumble. BEAUTIFUL (if I do say so myself!!!)!
I still have to finish four more, but I am feeling a bit better about it all. Will I ever do another charm swap? Probably not. I HATE the repetition! But did it help me learn new things and practice the skills I have? ABSOLUTELY!
Now, I'm off to see a man about a bunch of scrap metal!
There are Metalsmiths of all levels in this group. From the novice (like myself) to seriously seasoned pro's! We like to think of ourselves as the "un-team Team and we welcome anyone....provided you give us your first name and DO NOT spam us! :D
Back around November we decided that we loved each others work so much that we wanted to share! At first it was suggested that we have a pendant swap! Well, I was all for this! This was an opportunity to really shine! It was going to be a masterpiece! Before I could finish dreaming, it had changed and now, we were doing a charm swap. Ok, still alright.....I think.
I immediately started sketching. I wanted to play on my strengths. *What were my strengths again?* Oh yeah, I have none. Well, maybe one; I am not afraid to REALLY screw up some metal! I mean I will try ANYTHING!! Usually with disastrous results, but hey that's how you learn, right? **Not to mention all the incredible scrap metal you produce!**
So I started with a triangle. My thinking being that 1) not everyone would be doing it and 2) it took less metal. (At this writing, silver prices are $18.44 a ounce!!!!) So I mark them and start cutting. NO GOOD! I wont be able to anything on them once I'm finished. Back to the drawing board.
November turns to December and all I have are sketches. Now I'm busy preparing for Christmas. Still no progress. That's when it hit me....wait to see what you get for Christmas, then you will know what to do.
Well I got a disc cutter, drill bits, a caliper and gift certificates to the supply house!
"The disc cutter will help", I think. "They are going to be round"!
STEP ONE: Determine a shape. Check!
So I order metal. Not much, but enough to make the charms. I have TONS of copper, but I haven't soldered it much before and I really want them to be silver!
STEP TWO: Order metal. Check.
The Sterling silver arrives and I cant wait to try out my new disc cutter. Okay, so lets just say, sometimes it worked and sometimes it didn't. **Operator problems** I was still able to get 10 usable discs from it. **And 3 unusable ones but we will refer to those as "future opportunities"!**
STEP THREE: Cut the metal. Check.Now I have to ask myself, "Where do we go from here"? I look at my sketches again....nothing there that speaks to me.
WAIT! I HAVE IT! I have been doing a series of pieces about water. I don't know why. I am not particularly fond of water except as my drink of choice but at least this is a direction. Ok. water, water, water....."the flow"! Why "the flow"? I guess because I have a hard time going with it; this will serve as a reminder!
STEP FOUR: Choose a design and make these bad boys! Check.
Now I'm on a roll! So I stamp "flow" onto them! "The" is irrelevant. That worked.
Now what? Okay, I have a huge amount of inexpensive aquamarines, so I add a setting! **YOU GO GIRL!!!** So far, so good!
I then add my "water" (Silver wire that I have hammered flat and curved around my settings). Still, all good!
Time to cut the settings. (This is where the problems started!) You see, I had this tank of fuel that was running out, but I INSISTED on using it until the bitter end. So I solder away, pickle, rinse, and start to cut the settings......RIP! Off comes the setting. Rocketing across the room and now a two hour search is underway! Okay, I recovered it. Not sure what happened but I will fix that later. Lets try another...RIP!!! What is going on?!?!
I RUN to the computer and ask the forum. Bad soldering or too long in the pickle is the response I get. I know it wasn't in the pickle too long, so bad soldering it is! Now I remember that I have soldered 5 settings before I changed that tank, and 5 it is! Five settings rip off!
Its okay, I'm cool. Ill fix them later. Work with what you have.
The biggest problem is, these suckers are little! It hard to hold onto them while you cut them! I mention this to my husband and he says, "Use your shelf paper". (Like he'd been doing this his entire life and this was the OBVIOUS answer!!!) But it worked!!!I repair one of the broken settings **just to see if I can**! Okay, Its holding up, but I'm getting anxious! What if they look like crap?
So I work on the six I have cut. I set the stones, polish and tumble. BEAUTIFUL (if I do say so myself!!!)!I still have to finish four more, but I am feeling a bit better about it all. Will I ever do another charm swap? Probably not. I HATE the repetition! But did it help me learn new things and practice the skills I have? ABSOLUTELY!
Now, I'm off to see a man about a bunch of scrap metal!
Subscribe to:
Comments (Atom)